Thursday 2 February 2017

Nissan Cabstar synchronize key

This synchronization is for Nissan Cabstar M20,

You need this procedure once you happen to duplicate a new key.

1. Close both door, sit tight on driver seat and lock the driver door.

2. Insert & pull out your new key into steering key lock for 5 times and leave the key in the lock, after this procedure driver door lock will unlock.

This mean you already activate the synchronization. 

3. Press the lock & unlock button on the new key and turn it to ACC (refer to Pic), and lock the driver door lock once again. 

4. Simultaneously turn the new key to ON position & press unlock button on the new key, 
Please note : if the driver door unlock that mean you are complete the synchronize or else please try again. Good luck.

(CN)
如果你不是搞修车的,这篇你应该永远都用不到。

匹配M20锁匙,
每当你複製新的锁匙你是需要匹配锁匙,以下是他的步驟,

1)关上车门,做在车内然后上锁。
2)插入新複製的锁匙在拔出,重复五回(最后锁匙要在锁内)
如果操作正确,驾驶车门会自动打开。
3)压複製锁匙的两个钮,然后转到ACC,在锁上驾驶车门锁
4)同时间转锁匙到‘ON’和按下开锁按钮。

 如果车门锁会开就是成功。

Monday 7 November 2016

XentryTab & Xentry Connect Update

1, Bought a Xentry tab and no one giving technical support?
2, Xentry tab can't work?
3, Would like to change language in Xentry Connect?

Here we have the solution. attached few copies of photo for your reference.
Just complete the licence.




W204 Engine Misfire



Car keep misfiring, replace spark plug, ignition coil and fault remain.
therefore decided to repair ecu, finally found the culprit & have a happy customer.
Attached two copies of photo for your reference.


(CN)
马赛地发动机失火,更换了火花塞和点火线圈都没用,
最后更新引擎电脑问题解决。
附上两张电脑照片然大家看看电脑长什么样。



Friday 2 September 2016

Nissan Qashqai J11 start / stop system failure

Nissan Qashqai J11 start / stop system failure, one of the reason might due to weak battery.



Monday 8 February 2016

HONDA Stream P0723, P0746, P0722

P0723 Output shaft speed sensor (Intermittent Failure)
P0746 A/T clutch pressure control solenoid valve 'A' stuff off
P0722 Output shaft speed sensor (intermittent failure)
P0718 Input shaft speed sensor (Intermittent Failure)

This is a RN6, while moving car can't travel above 2000 rpm, speedometer gear position 'D' keep flashing and the engine warning light ON. Retrieve the fault code as shown above.

After go for the simple analyst P0746 is because of solenoid located below the Airbox
it might because of transmission internally faulty or solenoid spoil.

P0723 and P0722 also very clear need to replace sensor.

The problem is when i am calling stockist they mentioned that is no output and input shaft sensor....
which make me confusing, so further study is require.

Therefore i got a copy of this illustration, as common sense parts 11 & 12 is the sensor i am require. item 11 should be input and item 12 is output. But the stockist replying me according EPC is indicated as pick up assy. so i decided to unplug connector to prove it. BINGO and i am in the right track. so the message here to the reader is don't be fool by the Honda EPC.

Item number 4