BMW 325 Footwell Module failure

Yesterday, one of my friend call up for urgent help on BMW 325 fault was power window couldn't operate, indicator no respond, seat belt couldn't auto inject., when he told me over the phone, first thing flash into my mind said it

Bentley Continental - story about ECM

Someone would like to send this Bentley for me to install ECM and I had rejected him due to security issue but he keep insisted, I though OK is fine probably something else, once car is here
it turned to change engine ECU again......   

For my dear follower if your happened to change engine ECU it involved

BMW 7 series E65 Parking brake failure !

Do not panic if you see the above error while driving your BMW 7 series E65, this error are telling

Launch X431 IV review

Today I would like to introduce this guy "X431 iv", this guy been around market for one year +-, same as previous model using Linux as operation system, speed is much more better then before.

"X431 iv" more curvy, using polish surface and left hand side using rugged rubber surface,

Mercedes W221 FRONT SAM BURNED

W221 was tow to workshop because couldn't crank, battery condition was fully charged but i had hesitate to check on starter and fuel pump because i smell a rat, a strong burning smell came from driver seat footwell, straightly i sense that is electronic component was burned and resulted vehicle to be towed.

Xentry DAS basic intro

This is Mercedes repairer must have diagnostic tool, in 3rd picture is the interface namely "SD Connect" it connect to OBD port and communicate with your "Compact 4" thru wire or wireless.
This diagnostic tool using window XP to run Mercedes in house softwares, it's contain "WIS",

BMW carburetor antique 7.17755.00 & 7.17052.02

For today world who still need BMW 1502 carburetor. still left one each.

7.17755.00 ( 71775500 ) & 7.17052.02 ( 71705202 )

ityescarx@gmail.com

Mercedes E-class service interval reset.

This is E-Class W211 service interval reset procedure (look at photo 1), it's also can apply on other model as well.

1st, turn your key to 1st stage (There is 3 stages for MB key lock, the last stage is to ignite engine)

How to check your engine oil level in AUDI Q5

1) Switch on ignition (MMI logo will show on screen)

2) Tap on "CAR" button, a list will display

3) Using knob to select oil level (you need to wait approximately 5minute to get the indication.) 

Q5 white smoke

Car came in because of owner topping up 4lt of engine oil which caused 8lt engine oil in total.
customer was mislead with the engine oil level indicator showed in MMI.

The correct way to top up engine oil is 1lt each time and wait a reasonably time for the MMI to reflect correct engine oil level.

Top up too much engine oil will resulted engine head float with oil, usually come together with misfire or engine stall (due to spark plug soak with oil). If have the chance start the engine then exhaust for sure will accompany with white color fume.

Next post I will introduced how to check engine oil level to lower down mistake (mean save your $).

Replace Audi Mechatronic

Owner complained reverse gear and 2nd gear abnormal during cruising, go thru diagnosed and found mechatronic actuator have malfunction, therefore proceed replace a new mechatronic.

During processing ensure mechatronic are hook on four catch at transmission (refer to 2nd pic) and adjust your gear actuators to exact dimension, that is 28mm or 32mm depend on mechatronic identification once you adjust the correct dimension it will be easy to hook it.

VW BEETLE - 16825 EVAP EMISSION CONTROL SYS

Check engine light "ON", therefore I'm using VCDS diagnose and found out EVAP had incorrect

Maserati Quattroporte

 





Car came with roof light problem, controller light blinking after check
is due to wiring connection issue, connect and reset, problem solved

VAS5054A and VAS

VAS5054 arrived and ready to use but before that you need to install VAS to move on. 

Below are the software look like, it can support VW, Audi, Skoda Bentley and a minor feature of Lamborghini. If you have valid account then you can access dealer network to program immobilizer, basic setting for mechatronic and some exclusive feature. 

I will update if i have a chance to log onto dealer network.